Package jmri.implementation

Class ResettingOffsetHighCvProgrammerFacade

  • All Implemented Interfaces:
    java.util.EventListener, Disposable, ProgListener, Programmer
    public class ResettingOffsetHighCvProgrammerFacade
extends AbstractProgrammerFacade
implements ProgListener
    Programmer facade, at this point just an example.

    This is for decoders that have an alternate high-CV access method for command stations that can't address all 1024. It falls back to that mode if the CS can't directly address an requested CV address. In the fall back, CVs from 0 to "top" are addressed directly. Above the top CV, the upper part of the address is written to a specific CV, followed by an operation to just the lower part of the address. The upper and lower parts are calculated using a supplied modulus, e.g. 100, and an indicator value that's added in. Finally, the specific CV is reset to zero to end the offset operation.

    For example, to write the value N to CV xyy, this will do (modulo = 100, indicator = 200):

    • Write 200+x*10 to CV7 where 10 is cvFactor, 200 is indicator and 7 is addrCV
    • Write N to CVyy
    • Write 0 to CV7

    This method is used by some Zimo decoders

    See Also:
    ProgrammerFacadeSelector

    • Constructor Detail

      • ResettingOffsetHighCvProgrammerFacade

        public ResettingOffsetHighCvProgrammerFacade​(Programmer prog,
                                             java.lang.String top,
                                             java.lang.String addrCV,
                                             java.lang.String cvFactor,
                                             java.lang.String modulo,
                                             java.lang.String indicator)
        Parameters:
        prog - the programmer this facade is attached to
        top - CVs above this use the indirect method
        addrCV - CV to which the high part of address is to be written
        cvFactor - CV to which the low part of address is to be written
        modulo - modulus for determining high/low address parts
        indicator - value added to calculation to split high and low parts

    • Method Detail

      • writeCV

        public void writeCV​(java.lang.String CV,
                    int val,
                    ProgListener p)
             throws ProgrammerException
        Description copied from class: AbstractProgrammerFacade
        Perform a CV write in the system-specific manner, and using the specified programming mode.

        Handles a general address space through a String address. Each programmer defines the acceptable formats.

        Note that this returns before the write is complete; you have to provide a ProgListener to hear about completion. For simplicity, expect the return to be on the GUI thread.

        Exceptions will only be thrown at the start, not during the actual programming sequence. A typical exception would be due to an invalid mode (though that should be prevented earlier)

        Specified by:
        writeCV in interface Programmer
        Overrides:
        writeCV in class AbstractProgrammerFacade
        Parameters:
        CV - the CV to write
        val - the value to write
        p - the listener that will be notified of the write
        Throws:
        ProgrammerException - if unable to communicate

      • readCV

        public void readCV​(java.lang.String CV,
                   ProgListener p)
            throws ProgrammerException
        Description copied from class: AbstractProgrammerFacade
        Perform a CV read in the system-specific manner, and using the specified programming mode.

        Handles a general address space through a String address. Each programmer defines the acceptable formats.

        Note that this returns before the write is complete; you have to provide a ProgListener to hear about completion. For simplicity, expect the return to be on the GUI thread.

        Exceptions will only be thrown at the start, not during the actual programming sequence. A typical exception would be due to an invalid mode (though that should be prevented earlier)

        Specified by:
        readCV in interface Programmer
        Overrides:
        readCV in class AbstractProgrammerFacade
        Parameters:
        CV - the CV to read
        p - the listener that will be notified of the read
        Throws:
        ProgrammerException - if unable to communicate

      • readCV

        public void readCV​(java.lang.String CV,
                   ProgListener p,
                   int startVal)
            throws ProgrammerException
        Description copied from interface: Programmer
        Perform a CV read in the system-specific manner, and using the specified programming mode, possibly using a hint of the current value to speed up programming.

        Handles a general address space through a String address. Each programmer defines the acceptable formats.

        On systems that support it, the startVal is a hint as to what the current value of the CV might be (e.g. the value from the roster). This could be verified immediately in direct byte mode to speed up the read process.

        Note that this returns before the write is complete; you have to provide a ProgListener to hear about completion. For simplicity, expect the return to be on the GUI thread.

        Defaults to the normal read method if not overridden in a specific implementation.

        Exceptions will only be thrown at the start, not during the actual programming sequence. A typical exception would be due to an invalid mode (though that should be prevented earlier)

        Specified by:
        readCV in interface Programmer
        Parameters:
        CV - the CV to read
        p - the listener that will be notified of the read
        startVal - a hint of what the current value might be, or 0
        Throws:
        ProgrammerException - if unable to communicate

      • programmingOpReply

        public void programmingOpReply​(int value,
                               int status)
        Description copied from interface: ProgListener
        Receive a callback at the end of a programming operation.
        Specified by:
        programmingOpReply in interface ProgListener
        Parameters:
        value - Value from a read operation, or value written on a write
        status - Denotes the completion code. Note that this is a bitwise combination of the various status coded defined in this interface.